Service Promise
I,After-sales service
To protect the legitimate rights and interests of consumers,the company sold products to the “three bags of”service,please take good care of the majority of users purchase a valid invoice,warranty card and the use of brochures,in a timely manner in order to get three bags of service.
1, three bags of range
Products based on the user’s manual provides that the right to operate,as a result of manufacturing quality is always important,or lead to vehicle parts and components can’t be used by companies to identify special maintenance technicians confirmed by the company commissioned by the company or dealer for the three bags of service.
2,not “three bags of “the scope of content:
1) not in accordance with the provisions of the use of brochures;
2) not in accordance with the requirements of the maintenance manual;
3) improper use or an accident or a collision caused by the wrongful use of fault;
4)irresistible factors;
5)without special consent to repair the maintenance department.
6)users to make alterations or demolition of parts caused by the decomposition of accessories or damage to the vehicle.
No purchase invoice,warranty card or card-vehicles are not inconsistent with the “three bags,”wearing parts,no consumables,”three bags”
II,the battery maintenance
1) the surface of the battery ,cables and bolts should be kept clean and dry a long time,if electrolyte leakage application wiped clean cotton yarn,and then rinse with water and dry,note:the cleaning process,tap water is strictly prohibited to enter inside the battery,so as to avoid leakage and increased self discharge,resulting in the vehicle running out of order.
2) Battery connections must be good.check the batteries regularly connect any fastening nut loose,so as not to cause a spark and burn column.
3) On the battery not to place any item can’t be negative battery is connected directly to avoid short circuit,damage batteries
4) After the battery discharge(regardless of traffic time and mileage),must charge the same day,the next day,not allowed to charge or charge more than 24 hours,or battery life will be affected.
5) Batteries used in the process,as the electroly te electrolysis of water and evaporation can cause increased density and surface decline(especially in the summer),it should be kept under check,add the electrolyte(in general can only add distilled water),rechargeable batteries in the end ,distilled water or with a density of 1400 of a dedicated lead-acid batteries dilute sulfuric acid electrolyte to adjust the density of 1.275+_0.005(25 degree)level with the same high level line.adjusted 0.5-1 hours to charge,so that the internal uniform.
6) Inside the battery are not allowed to fail into the hands of any impurities,add liquid used in the apparatus should be kept clean to avoid impurities into the battery inside.
7) Drivers in the running,at any time to observe the instructions of the battery meter(instrument panel on the power grid-beating table,to stop running,in time charge),it is estimated that the vehicle’s mileage,so as not to charge the vehicle can not return in time charge,batteries have been caused by discharge and shorten the useful life.
8) Vehicles if not for a long time,the battery should be full of power after the store,and every halfa month to a charge,charge time to 24 hours.
9) Charge,the vehicle should be grateful if you put good air circulation,and open the battery cover in order to avoid an accident.
10) Good and sufficient power,the battery cover tightly covered()check whether or not plug the pores plaza,should be clear if).
11) Batteries used in the process,the monthly charge should be a balance
III,charge use and maintenance
1) AC power outlet charger with the AC power plug to match
2) AC voltage should be more stable,the change should not exceed 220v +_10%range.
3) Charge operation:a,disconnect the power supply vehicle lock switch b,charging plug and socket body charge connected to c plug power and the city of power points and connected
4) Connected to the power charger,the wiring in the right time when the power indicator light,1-30A-charge current bright lights all the way filling heng,heng 2nd charge indicator light,the charge time status power deficit over the next 10 hours as well.
5) Charging process of change is as follows:the first phase of the 25a constant current charging about 6 hours;the second phase of the charging voltage of about 3 hours;floating into the final stage,at this time,the floating lantern festival light,the charge current only bright light 1-2 only,the fans stop spinning.saturated floating into the lights phases that have sufficient battery power.
6) To be full of battery power,or any need to shut down,the need to disconnect input power charger and then disconnect the battery and charger connection.
The main performance indicators:
1. input voltage:180v -240v,50hz
2. charging voltage:48v
3. current charge current:25a
4. voltage charge voltage:60v-66v(with the ambient temperature change)
IV. traction motor maintenance and repair
1) temperature to -25 degree+40 degree.
2) Does not allow motors idling.
3) In the air should not contain an explosive gas.
4) Often the case on the and and other material shuadiao adhesive,so as not to affect cooling.
Serial number Failure phenomenon Reason
1 All black copper Pressure not to brush
2 For the film by an order of a group of black Pianpian points,or change to the structure-coil short-circuit, the chip-for-shu points and bad welding wire or circuit
3 For the black film,but could not come to any rules Commutator center of the commutator surface displacement and not a round,uneven
4 Brush wear,color and the breakdown of Vibration machine,brush and brush is too large gap between the boxes,brush box and the distance between the commutator surface work is too large.loading between commutator to highlight the mother,material adverse brush,brush wrong brand
5 Big spark Electrical overload,dirty commutator,commutator not smooth or a round piece of mica or part of the film for prominent,brush the ground is not good,not great pressure on the brush,brush right brand,brush in the brush box stuck inside immobility,loose brush frame or vibration,the magnetic polarity of the order and not to shun charge
6 Brush and brush line change fever Brush major spark,with the soft wire brush between bad and soft wire is not a small cross-sectional area
7 Brush a noise Commutator surface is not smooth
| Serial number | Failure phenomenon | Reason |
|---|---|---|
| 1 | All black copper | Pressure not to brush |
| 2 | For the film by an order of a group of black | Pianpian points,or change to the structure-coil short-circuit, the chip-for-shu points and bad welding wire or circuit |
| 3 | For the black film,but could not come to any rules | Commutator center of the commutator surface displacement and not a round,uneven |
| 4 | Brush wear,color and the breakdown of | Vibration machine,brush and brush is too large gap between the boxes,brush box and the distance between the commutator surface work is too large.loading between commutator to highlight the mother,material adverse brush,brush wrong brand |
| 5 | Big spark | Electrical overload,dirty commutator,commutator not smooth or a round piece of mica or part of the film for prominent,brush the ground is not good,not great pressure on the brush,brush right brand,brush in the brush box stuck inside immobility,loose brush frame or vibration,the magnetic polarity of the order and not to shun charge |
| 6 | Brush and brush line change fever | Brush major spark,with the soft wire brush between bad and soft wire is not a small cross-sectional area |
| 7 | Brush a noise | Commutator surface is not smooth |
Fifth,the speed control device maintenance
The use of the vehicle speed controller to use advanced u.s. technology to control production,using high-frequency mos technology to achieve smooth,quiet and highly efficient energy-saving vehicle speed and torque control.
Regular maintenance:
Check a contact is good contact between the contact,whether or adhesions,whether or not moving any mechanical contact card to die;
Check the accelerator potentiometer contact is good;
Check the direction switch,breaking performance is good;
Check motor,batteries and power controller modul of the connection between the state is good
Note:
In case of power outages to be checked,this is in at least three months;turn off the power locks, power control unit to maintain the filter capacitor discharge for a few minutes of time,should not have the electrical components to wash with water!can be used high-pressure gas or brush to remove dust.
Brake parts
1) 30kgf about the use of force to the brakes,the pedal to check the distance between the anterior body,the minimum distace of not less than 50mm
2) Pedal car in 30kgf around,parking limit should be rliable and accurate,the limit should be complete braking ,or need adjustment.
3) Brake fluid used in brake fluid is a synthetic dot3
4) Transmission capacity in the use of gear oil 85w/90gl-4,the amount of 1.5liters.
5) Lubrication point:a turn around the direction of aircraft to support b section bearing parts of the brake pedal d rotation parts
The new carts go together
In order to ensure the use of vehicle performance,increase the reliability and service life of the vehicle,should be the largest electrical load in order to work before their run-in position to carry out this requirement of the new combined time of one month away,and the following specification:
1) new car before walking together,we must double-check all kinds of oil,water ,liquid capacity,such as inadequate,provision should be added;tires should be in line with 155/65r13,tubeless,with the tire pressure should be on the demarcation of the pressure value
2) as far as possible not to bad road conditions roads
3) carry out regular checks of the connection and fastening parts of the fastener.
Notes
1) front axle bearings must be requested by the statement added grease,gear oil
2) as far as possible not to bad road conditions roads
3) carry out regular checks of the connection and fastening parts of the fasternr.
Notes
1) front axle bearing must be requested by the statement added grease,gear oil
2) check every three months must adhere to the brake shoe wear.
3) Once every three months electrical system(especially the main circuit)of any loose fasteners,must maintain good contacts at the same time,the plug-in access to check and found that defects should be corrected in a timely manner,the dust deposition use of low pressure air blowing net.
4) Due to bad electrical contact ,heat will be ,therefore,to keep contact with a heat –of-contact state.
5) Replacement fuse,must check the new fuse rated current is correct.
6) In the vehicle maintenance and repair,in order to ensure security,should be dismantled on the positive battery power.
7) Prohibited mengcai accelerator and the accelerator to move frequently ,so as not to shorten the life of electronic control.
8) Other liquids will be strictly prohibited(battery additives,mineral water,water,etc.)joined the batteries need to add distilled water or special electrolyte batteries.
9) Is strictly prohibited in the downhill when the high speed turn should slow down and turn downhill when the crew to remind lay the rails,in order to avoid an acciedent.
10) Children is strictly prohibited in the vehicle play,moving the child should be sitting in the middel and the protection of adults.
11) Avoid a sharp turn.
12) Case of rain or the wind is strong and the weather,the road is wet and shlippery,lowtraffic speeds.
13) At least once a month of pneumatic thires in the original proposed scope of the tire.
Maggie Choi
Hongkong CIMVECO Machinery&Electronical Equipment Limited
Mobile: 0086-13681589927
Tel: 0086-10-63871631
Fax: 0086-10-63871631
EMAIL: maggie@theelectricalbicycle.com
MSN: electronical1@hotmail.com
http://www.theelectricalbicycle.com
Yahoo id:maggiechoi96@yahoo.com
- Electric Car
- Electric Car
- Electrical bike
- Folding Electrical Bike
- Electrical cargo tricycle
- Spare parts
Maggie choi
Hongkong CIMVECO Machinery&Electronical Equipment Limited
Mobile: 0086-13681589927
Tel:0086-10-63871631
Fax:0086-10-63871631
EMAIL: maggie@theelectricalbicycle.com
MSN: electronical1@hotmail.com
http://www.theelectricalbicycle.com
Yahoo id:maggiechoi96@yahoo.com